MOBILE MODULE

The device supports 5G Sub-6 GHz SA/NSA with download speeds of 2.4 / 3.4 Gbps (4×4 MIMO) and upload speeds of 900 / 550 Mbps (2×2 MIMO). 4G LTE Cat 19 provides downlink up to 1.6 Gbps and uplink Cat 18 up to 200 Mbps. 3G connectivity offers 42 Mbps downlink and 5.76 Mbps uplink.

3GPP RELEASE

Release 16.

ESIM

Consumer type eSIM, profile download and removal operations, up to 7 eSIM profiles; does not include data plans.

SIM SWITCH

2 SIM cards, auto-switch cases: weak signal, data limit, SMS limit, roaming, no network, network denied, data connection fail, SIM idle protection.

STATUS

IMSI, ICCID, operator, operator state, data connection state, network type, bandwidth, connected band, signal strength (RSSI), SINR, RSRP, RSRQ, EC/IO, RSCP, data sent/received, LAC, TAC, cell ID, ARFCN, UARFCN, EARFCN, MCC, and MNC.

SMS

SMS status, SMS configuration, EMAIL to SMS, SMS to EMAIL, SMS to HTTP, SMS to SMS, scheduled SMS, SMS autoreply, SMPP.

USSD

Supports sending and reading Unstructured Supplementary Service Data messages.

BLOCK / ALLOW LIST

Operator block/allow list (by country or separate operators).

BAND MANAGEMENT

Band lock, used band status display.

SIM IDLE PROTECTION SERVICE

Provides the possibility to configure the router to periodically switch to the unused SIM card and establish a data connection in order to prevent the SIM card from being blocked.

SIM PIN CODE MANAGEMENT

SIM PIN code management enables setting, changing, or disabling the SIM card’s PIN.

APN

Auto APN.

BRIDGE

Direct connection (bridge) between mobile ISP and device on LAN.

PASSTHROUGH

Router assigns its mobile WAN IP address to another device on LAN.

FRAMED ROUTING

Framed routing: support an IP network behind 5G UE.

ETHERNET

2 x ETH ports (can be configured as WAN), 10/100/1000 Mbps, compliance with IEEE 802.3, IEEE 802.3u, 802.3az standards, supports auto MDI/MDIX crossover.

POE IN

1 x PoE In.

POE STANDARDS (IN)

802.3af/at.

POE OUT

1 x PoE Out.

POE STANDARDS (OUT)

802.3af Alternative B.

POE MAX POWER PER PORT (AT PSE)

15 W Max (power supply unit dependent).

NETWORK ROUTING

Static routing, dynamic routing (BGP, OSPF v2, RIP v1/v2, EIGRP, NHRP), policy-based routing.

NETWORK PROTOCOLS

TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, SFTP, FTP, SMTP, SSL/TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet, SMPP, SNMP, MQTT, Wake On Lan (WOL), VXLAN.

VOIP PASSTHROUGH SUPPORT

H.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets.

CONNECTION MONITORING

Ping Reboot, Wget Reboot, Periodic Reboot, LCP and ICMP for link inspection.

FIREWALL

Port forward, traffic rules, custom rules, TTL target customisation.

FIREWALL STATUS PAGE

View all your firewall statistics, rules, and rule counters.

PORT MANAGEMENT

View device ports, enable and disable each of them, turn auto-configuration on or off, change their transmission speed, and so on.

NETWORK TOPOLOGY

Visual representation of your network, showing which devices are connected to which other devices.

DHCP

Static and dynamic IP allocation, DHCP relay, DHCP server configuration, status, static leases: MAC with wildcards.

QOS / SMART QUEUE MANAGEMENT (SQM)

Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e.

DDNS

Supported >77 service providers, others can be configured manually.

DNS OVER HTTPS

DNS over HTTPS proxy enables secure DNS resolution by routing DNS queries over HTTPS.

NETWORK BACKUP

VRRP, wired options, each of which can be used as an automatic Failover.

LOAD BALANCING

Balance internet traffic over multiple WAN connections.

HOTSPOT

Captive portal (hotspot), internal/external Radius server, Radius MAC authentication, SMS authorisation, SSO authentication, internal/external landing page, walled garden, user scripts, URL parameters, user groups, individual user or group limitations, user management, 9 default customisable themes and optionality to upload and download customised hotspot themes.

SSHFS

Possibility to mount remote file system via SSH protocol.

VRF SUPPORT

Initial virtual routing and forwarding (VRF) support.

TRAFFIC MANAGEMENT

Real-time monitoring, wireless signal charts, traffic usage history.

SECURITY – AUTHENTICATION

Pre-shared key, digital certificates, X.509 certificates, TACACS+, Internal & External RADIUS users authentication, IP & login attempts block, time-based login blocking, built-in random password generator.

SECURITY – FIREWALL

Preconfigured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI, DMZ, NAT, NAT-T, NAT64.

ATTACK PREVENTION

DDoS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN-RST, X-mas, NULL flags, FIN scan attacks).

VLAN

Port and tag-based VLAN separation.

MOBILE QUOTA CONTROL

Mobile data limit, customizable period, start time, warning limit, phone number.

WEB FILTER

Blacklist for blocking unwanted websites, whitelist for specifying allowed sites.

ACCESS CONTROL

Flexible access control of SSH, Web interface, CLI, and Telnet.

TPM

Identification and authentication module, TPM 2.0 standard.

CERTIFICATE MANAGER

Certificate creation tool allows creating CA, server, client, Let’s Encrypt, SCEP certificates.

802.1X

Port-based network access control server.

VPN – OPENVPN

Multiple clients and a server can run simultaneously, 27 encryption methods.

OPENVPN ENCRYPTION

DES-CBC 64, RC2-CBC 128, DES-EDE-CBC 128, DES-EDE3-CBC 192, DESX-CBC 192, BF-CBC 128, RC2-40-CBC 40, CAST5-CBC 128, RC2-64-CBC 64, AES-128-CBC 128, AES-128-CFB 128, AES-128-CFB1 128, AES-128-CFB8 128, AES-128-OFB 128, AES-128-GCM 128, AES-192-CFB 192, AES-192-CFB1 192, AES-192-CFB8 192, AES-192-OFB 192, AES-192-CBC 192, AES-192-GCM 192, AES-256-GCM 256, AES-256-CFB 256, AES-256-CFB1 256, AES-256-CFB8 256, AES-256-OFB 256, AES-256-CBC 256.

IPSEC

XFRM, IKEv1, IKEv2, with 14 encryption methods for IPsec (3DES, DES, AES128, AES192, AES256, AES128GCM8, AES192GCM8, AES256GCM8, AES128GCM12, AES192GCM12, AES256GCM12, AES128GCM16, AES192GCM16, AES256GCM16).

GRE

GRE tunnel, GRE tunnel over IPsec support.

PPTP, L2TP

Client/Server instances can run simultaneously, L2TPv3, L2TP over IPsec support.

STUNNEL

Proxy designed to add TLS encryption functionality to existing clients and servers without any changes in the program’s code.

DMVPN

Method of building scalable IPsec VPNs, Phase 2 and Phase 3, dual hub support.

SSTP

SSTP client instance support.

ZEROTIER

ZeroTier VPN client support.

WIREGUARD

WireGuard VPN client and server support.

TINC

Tinc offers encryption, authentication, and compression in its tunnels. Client and server support.

TAILSCALE

Tailscale offers speed, stability, and simplicity over traditional VPNs. Encrypted point-to-point connections using the open-source WireGuard protocol.

OPC UA

Supported modes: Client, Server.
Supported connection types: TCP.

MODBUS

Supported modes: Server, Client.
Supported connection types: TCP.
Custom registers: MODBUS TCP custom register block requests, which read/write to a file inside the router and can be used to extend MODBUS TCP Client functionality.
Supported data formats: 8-bit: INT, UINT; 16-bit: INT, UINT (MSB or LSB first); 32-bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII.

DATA TO SERVER

Protocol: HTTP(S), MQTT, Azure MQTT.
Data to server: Extract parameters from multiple sources and different protocols, and send them all to a single server; Custom LUA scripting allows scripts to utilize the router’s Data to Server feature.

MQTT GATEWAY

Modbus MQTT Gateway allows sending commands and receiving data from MODBUS Server through MQTT broker.

DNP3

Supported modes: Station, Outstation.
Supported connection: TCP.

DLMS/COSEM

DLMS support: Standard protocol for utility meter data exchange.
Supported modes: Client.
Supported connection types: TCP.

API

Teltonika Networks Web API (beta) support. Expand your device’s possibilities by using configurable API endpoints to retrieve or change data. More information: Teltonika Developers.

MONITORING & MANAGEMENT – WEB UI

HTTP/HTTPS, status, configuration, firmware update, CLI, troubleshoot, multiple event log servers, firmware update notifications, system log, kernel log, Internet status.

FOTA

Firmware update from server, automatic notifications.

SSH

SSH (v1, v2) support.

EMAIL

Receive email message status alerts of various services.

SMS

SMS status, SMS configuration.

CALL

Reboot, status, mobile data on/off, output on/off, answer/hang-up with a timer.

TR-069

OpenACS, EasyCwmp, ACSLite, tGem, LibreACS, GenieACS, FreeACS, LibCWMP, Friendly tech, AVSystem.

MQTT

MQTT Broker, MQTT publisher.

SNMP

SNMP (v1, v2, v3), SNMP Trap, brute force protection.

JSON-RPC

Management API over HTTP/HTTPS.

RMS

Teltonika Remote Management System (RMS).

IOT PLATFORMS – THINGWORX

Allows monitoring of WAN type, WAN IP, mobile operator name, mobile signal strength, and mobile network type.

IOT PLATFORMS – CUMULOCITY

Allows monitoring of device model, revision and serial number, WAN type and IP, mobile cell ID, ICCID, IMEI, connection type, operator, signal strength. Supports reboot and firmware upgrade actions.

IOT PLATFORMS – AZURE IOT HUB

Can be configured with Data to Server to send all available parameters to the cloud. Supports direct method execution of RutOS API calls, and Plug and Play integration with Device Provisioning Service for zero-touch device provisioning.

IOT PLATFORMS – AWS IOT CORE

Utility to interact with AWS cloud platform. Supports calling the device’s API using AWS Jobs functionality.

SYSTEM CHARACTERISTICS – CPU

MediaTek dual-core 880 MHz, MIPS1004Kc.

RAM

256 MB, DDR3.

FLASH STORAGE

16 MB serial NOR flash, 256 MB serial NAND flash.

FIRMWARE / CONFIGURATION – WEB UI

Update firmware from file, check firmware on server, configuration profiles, configuration backup.

FOTA

Update firmware.

RMS

Update firmware/configuration for multiple devices at once.

KEEP SETTINGS

Update firmware without losing current configuration.

FACTORY SETTINGS RESET

A full factory reset restores all system settings, including IP address, PIN, and user data to the default manufacturer configuration.

FIRMWARE CUSTOMISATION – OPERATING SYSTEM

RutOS (OpenWrt-based Linux OS).

SUPPORTED LANGUAGES

Busybox shell, Lua, C, C++, Python, Java in package manager.

DEVELOPMENT TOOLS

SDK package with build environment provided.

GPL CUSTOMIZATION

You can create custom, branded firmware and web page applications by changing colours, logos, and other elements to fit your or your clients’ needs.

PACKAGE MANAGER

Service used to install additional software on the device.

POWER – CONNECTOR

RJ45 Socket.

INPUT VOLTAGE RANGE

42.5–57.0 VDC, reverse polarity protection, voltage surge/transient protection.

INPUT VOLTAGE RANGE FOR POE

42.5–57.0 VDC, reverse polarity protection, voltage surge/transient protection.

POWER CONSUMPTION

Idle: < 2.5 W / Max: < 9 W / PoE Max < 24 W.

PHYSICAL INTERFACES – ETHERNET

2 x RJ45 ports, 10/100/1000 Mbps.

STATUS LEDS

3 x mobile connection type, 3 x mobile connection strength, 4 x ETH status LEDs.

SIM

2 x SIM slots (Mini SIM – 2FF), 1.8 V/3 V.

POWER

RJ45, PoE In, 42.5–57.0 VDC.

ANTENNAS

4 x internal antennas.

ANTENNAS SPECIFICATIONS

4 x 617–960 / 1695–2690 / 3300–4200 / 4200–5000 MHz, 50 Ω, VSWR <3.5, gain <4.9 dBi, omnidirectional.

RESET

Reboot/User default reset/Factory reset button.

PHYSICAL SPECIFICATION – CASING MATERIAL

Plastic (PC+ASA).

DIMENSIONS (W × H × D)

110 × 49.3 × 235 mm.

WEIGHT

385 g.

MOUNTING OPTIONS

Mounting bracket (for vertical flat surface or pole mounting).

OPERATING ENVIRONMENT – TEMPERATURE

-40 °C to 55 °C.

OPERATING HUMIDITY

10% to 90% non-condensing.

INGRESS PROTECTION RATING

IP55.

REGULATORY & TYPE APPROVALS – REGULATORY

CE, UKCA, RCM, CB, EAC, UCRF, WEEE.

EMC EMISSIONS & IMMUNITY – STANDARDS

EN 55032:2015 + A11:2020 + A1:2020; EN 55035:2017 + A11:2020; EN IEC 61000-3-2: 2019 + A1:2021; EN 61000-3-3: 2013 + A1:2019 + A2:2021; EN 301 489-1 V2.2.3; EN 301 489-52 V1.2.1.

ESD

EN 61000-4-2:2009.

RADIATED IMMUNITY

EN IEC 61000-4-3:2020.

EFT

EN 61000-4-4:2012.

SURGE IMMUNITY (AC MAINS POWER PORT)

EN 61000-4-5:2014 + A1:2017.

CS

EN 61000-4-6:2014.

DIP

EN 61000-4-11:2020.

RF – STANDARDS

EN 301 908-1 V13.1.1, EN 301 908-2 V13.1.1, EN 301 908-13 V13.1.1, EN 301 908-25 V15.1.1_15.0.6.

SAFETY – STANDARDS

CE: EN IEC 62368-1:2020 + A11:2020, EN 62311:2020.
RCM: AS/NZS 62368.1:2022.
CB: IEC 62368-1:2018.